| |
SafeMount Innovative Mounting
Solutions |
|
What Is SafeMount?
|
| |
 |
Safemount is an engineered, universal, precision bracket for mounting
positioners, switch boxes and position indicators etc. to actuators. |
 |
|
Benefits And Features
Of SafeMount
|
| |
Time Savings
- No special brackets to order or have made
- Correct stainless nuts and bolts supplied
- Precise pressure die cast means it fits first
time, every time
- No selection guesswork - only 3 sizes fit all
actuators and accessories
Eliminate Mounting Problems
- Stronger than fabricated brackets
- More accurate than fabricated brackets
- Fully enclosed design provides safety
to assemblers and operators
- Standard and optional corrosion
protection means a longer service life
Economical
- Lower priced than any custom
manufactured bracket
- Install in just minutes
- No rework with die cast accuracy
- All mounting hardware supplied
- Low inventory costs with only 3 sizes
for all applications
Increased Accessory Life
- Precision parallel faces eliminate side loads to shafts and
bearings
- Accurate, consistent specified height means no up thrust to
positioners and switch boxes
- Correct supplied mounting hardware assures secure attachment
High Quality
- Large capital investment in Aluminium
pressure die castings means the SafeMount is low in cost but high in
quality. Quality is assured through certified ISO 9001 management
systems.
Stainless Steel Hardware
- The SafeMount is supplied with all
necessary Stainless Steel bolts and washers.
Safety
- The SafeMount is fully enclosed.
Fingers cannot get at the rotating shaft giving plant personnel
maximum protection; an approaching International Safety Standard.
Reduced Inventory Costs
- No need to keep high inventories of high cost,
custom made brackets. A maximum of three sizes will cover all your
accessory to actuator requirements.
Strong & Accurate
- The SafeMount is engineered to be strong and
accurate. No more bent and/or flexing mounting brackets. No more
poorly aligned mounting holes. No more damage to accessory bearings
and shaft seals. No more cut fingers from sharp bracket edges.
SafeMount will pass the technicians "ladder" test.
Corrosion Resistance
- Our standard VEP50 ELECTROPHORETIC bonded black
coating gives over 2000 hours protection in a standard salt spray
corrosion test. Also available in CORROGARD 941 Fluoropolymer bonded
coating for more aggressive environments.
Accessory mounting Holes
- The SafeMount fits both the old 2 1/4"
X 2 1/4" mounting square and the VDI/VDE
standard.
|
|
|
Back to Top |
|
Dimensional Diagrams
|
| |
 |
SAFEMOUNT SM 80/20
VDI/VDE 80mm x 30mm (3.15" x 1.18").
To Suit 20mm (0.79") high Namur Pinion.
Overall height 45mm (1.77").
1) 4 holes 6mm (0.24") DIA. Mounting Hardware on 80 x 30 (3.15" x 1.18")
VDI/VDE
2) 4 holes 7mm (0.28") DIA. Mounting Hardware on ISO 50mm (1.97") PCD.
3) 4 holes 9mm (0.35") DIA. Mounting Hardware on 57.1mm (2.25") square
(3.18" PCD). |
| |
|
| |
 |
SAFEMOUNT SM 80/30
VDI/VDE 80mm x 30mm (3.15" x 1.18").
To Suit 30mm (1.18") high Namur Pinion.
Overall height 55mm (2.17").
1) 4 holes 6mm (0.24") DIA. Mounting Hardware on 80 x 30 (3.15" x 1.18")
VDI/VDE
2) 4 holes 7mm (0.28") DIA. Mounting Hardware on ISO 50mm (1.97") PCD.
3) 4 holes 9mm (0.35") DIA. Mounting Hardware on 57.1mm (2.25") square
(3.18" PCD). |
| |
|
| |
 |
SAFEMOUNT SM 130/30
VDI/VDE 130mm x 30mm (5.12" x 1.18").
To Suit 30mm (1.18") high Namur Pinion.
Overall height 55mm (2.17").
1) 4 holes 6mm (0.24") DIA. Mounting Hardware on 130 x 30 (5.12" x
1.18") VDI/VDE
2) 4 holes 7mm (0.28") DIA. Mounting Hardware on ISO 50mm (1.97") PCD.
3) 4 holes 9mm (0.35") DIA. Mounting Hardware on 57.1mm (2.25") square
(3.18" PCD). |
| |
Back to Top |
|
|
